FENIX TK35UE FLASHLIGHT – 2018 EDITION (3200 Lumens)

If you're making a summit push in the hours before dawn or unforseen circumstances keep you out on the trail far later than expected, your effort will be far safer and simpler with the Fenix's TK35UE Flashlight lighting the way. Specifically designed for emergency situations, the TK35UE emits a seriously powerful beam brighter than a car's high beams when called upon to illuminate rocky scrambles and uneven ground. If you choose, you can cast a 2,000-lumen column of light over 1,000 feet in front of you, or switch into modes with a strobe light for summit attempts or an S. O. S. for rescue situations. The TK35UE excels at every level. Flashlight Size: Length: 6.5″ (164.5mm) Body Diameter: 1.7″ (43mm) Head Diameter: 1.9″ (48mm) Flashlight Weight: 10.1 oz. (286g) weight excluding batteries Batteries: Two 18650 rechargeable Li-ion batteries (not included) NOTE: The light will not work with flat-top 18650s.  We recommend any of the ARB-L18 series from Fenix. Included: Holster, lanyard, spare O-ring and USB charging cable Warranty: Limited Lifetime Guarantee from Fenix Lighting USA   ANSI FL-1 RATING MODE OUTPUT LUMENS MAXIMUM RUNTIME MAXIMUM DISTANCE MAXIMUM INTENSITY IMPACT RESISTANCE WATERPROOF Eco 20 152h 66ft (20m) 100cd Low 100 38h 40min 180ft (55m) 760cd Medium 350 10h 50min 328ft (100m) 2500cd High 1000 3h 40min 554ft (169m) 7140cd Turbo - Tactical 2000 2h 764ft (233m) 13600cd Turbo - Outdoor 3200 1h 30min 984ft (300m) 22500cd Strobe 3200 – – – 1m IP68, waterproof underwater to 2m/dust proof   ADDITIONAL FEATURES Cree XHP70 LED, with lifespan of 50,000 hours Powered by two 18650 rechargeable Li-ion batteries Innovative toggle switch for free switching between tactical, outdoor and lockout modes Micro USB rechargeable battery holder Instant off and lockout function effectively avoids accidental activation Instant strobe Battery level indication and low-voltage warning Digitally regulated output maintains constant brightness Reverse polarity protection to protect from improper battery insertion Made of durable high-strength and oxidation-resistance aluminum Premium type HAIII hard-anodized anti-abrasive finish Toughened ultra-clear glass lens with an anti-reflective coating Notice: The mentioned parameters (lab-tested by using two Fenix ARB-L18-3500 18650 rechargeable Li-ion batteries) may vary between flashlights, batteries and environment. Operating Instruction Switches The big one is the tactical switch. The small one is the functional switch. The toggle switch is for mode switching. Mode Switching In any state, turn the toggle switch from left to right, to select between tactical, outdoor and lockout modes. Tactical Mode Tap the Tactical switch to momentarily turn on the light, release it the light will go out. Fully press the Tactical switch to constantly turn on the light, press once again to turn off the light. With the light switched on, press and hold the Functional switch over 1 second to enter Strobe, press and hold the Functional switch again for 1 second to return to General mode. In Tactical mode, only Turbo on General mode and Strobe on Flash mode are available. Outdoor Mode Tap the Tactical switch to momentarily turn on the light, release it the light will go out. Fully press the Tactical switch to constantly turn on the light, press once again to turn off the light. With the light switched on, single click the Functional switch to cycle through Eco→Low→Med→High→Turbo. Press and hold the Functional switch over 1 second to enter Flash mode, press and hold the Functional switch again for 1 second to return to General mode. In Flash mode, single click the Functional switch to cycle through Strobe→SOS. Lockout Mode In any state, turn the toggle switch to off mark, the light will go out and enter lockout status, then the Tactical and Functional switches don’t work. For security, when Tactical switch is switched on, the battery level indicator on the Functional switch will be lit on to remind that Tactical switch is switched on, turn off the Tactical switch, the battery level indicator will go out. Instant Strobe With the light switched off, press the Functional switch to enter instant Strobe, release it the light will return to off status. With the light switched on instant Strobe, then simultaneously press the Tactical switch to constantly lock on Strobe mode. Intelligent Memory Circuit The light memorizes the last selected brightness level on Outdoor mode. When turned on again the previously used brightness level will be recalled. Strobe is factory defaulted each time the light is turned on Flash mode. Boot-up Battery Level Indication Each time the light is turned on, the battery level indicator will automatically display the battery status for 3 seconds. Green constant on: saturated Green flashes: sufficient Red constant on: poor Red flashes: critical Note: This only works on rechargeable LI-ion 18650 battery. Intelligent Protection The light will accumulate a lot of heat when it is working at Turbo mode. When the light is overheated up to 65 ℃ or above, the flashlight will automatically step down a few lumens to reduce the temperature; when the temperature is lower than 65 ℃, the output will gradually return to Turbo output level. Low-voltage Warning When the voltage level drops below the preset level with the light switched on, low voltage warning will be activated automatically, then the battery level indicator on the Functional switch will flash red to remind battery replacement or charging. The flashlight is programmed to step down automatically to a lower brightness level until Eco output is reached. To ensure normal use, the flashlight will not turn off until the battery level runs out or once the battery over-discharging protection activates. Note: This only works on 18650 Li-ion battery. Charging The battery holder features charging function with a standard Micro USB port. Take the battery holder out of the light, plug the USB port of the charging cable into any USB power supply. and plug the Micro USB side of the charging cable into the charging port of the battery holder. The charging indicator will display red while charging, and will turn to solid green when fully charged. Note: Avoid conductive object like coins, screws and keys when takes the battery holder out of the light, to protect from circuit damage caused by electrode short circuit. Battery Replacement Unscrew the head to take out the battery holder, and then insert the batteries in accordance with the polarity marks. After loading the batteries into the holder, insert the holder with its convex top towards the light tail. Screw the head back on. Usage and Maintenance Disassembling the sealed head can cause damage to the light and will void the warranty. Fenix recommends using excellent quality battery. If the flashlight will not be used for an extended period, remove the battery, or the flashlight could be damaged by electrolyte leakage or battery explosion. Long-term use can result in O-ring wear. To maintain a proper water seal, replace the ring with an approved spare. Periodic cleaning of the battery contacts improves the flashlight’s performance as dirty contacts may cause the flashlight to flicker, shine intermittently or even fail to illuminate for the following reasons: A: The batteries need replacing. Solution: Replace batteries (Ensure batteries are inserted according to the manufacturer’s   specifications). B: The threads, PCB board contact or other contacts are dirty. Solution: Clean the contact points with a cotton swab soaked in rubbing alcohol. C: The battery protection board is in a protective state and unable to free from it. Solution: Take out the battery holder and replace it, or replace the batteries. If the above methods don’t work, please contact your authorized distributor. Warning This flashlight is a high-intensity lighting device capable of causing eye damage to the user or others. Avoid shining the flashlight directly into anyone’s eyes.